G-CVO -Gas Orifice Fitting Control Valve Orifice, 3/8" Male Gas Flare x Male NPT

G-CVO

G-CVO - Gas Burner Orifice Fitting Control Valve, 3/8" MGF x 1/8" or 1/4" MNPT. For any gas burner.

► Custom drilling to other orifice sizes by request. No extra charge.

►   This needle valve will replace the existing Male NPT orifice fitting.
       Gives control over the flame height right in front of the burner.

► Generally High Pressure cast burners use a #61 orifice.
       Low pressure and natural gas burners require a larger orifice size,
       depending on the Btu's of the burner. If you are unsure
       send us a picture of the burner and we will help you select.

We offer free shipping to 48 U.S. States. Wts.1.9 oz, 2.2 oz, 2.7 oz.

G-CVO125 Control Valve Orifice Gas Fitting
G-CVO250 Control Valve Orifice Gas Fitting

$39.95

Gas Orifice Fitting Control Valve Orifice, 3/8 Male Gas Flare x Male NPT, for any gas burner

CVO - Gas Burner Control Valve Orifice Fitting , 3/8" MGF x MNPT

CVO

CVO - Gas Burner Control Valve Orifice for 1/8" or 1/4" NPT Burner Inlet

Select a CVO250 for a Pipe Burner. For a Cast Iron Burner the correct CVO can be selected from the drop down menu of the burner.

What is a Control Valve Orifice?

The CVO250 needle control valve with integral orifice will allow one to fine control the level of the burner flames right at the venturi as opposed to controlling the flame height at the more remote location like at the propane tank regulator or the natural gas source.

A control valve orifice fitting will work on practically any burner if the orifice is drilled to the proper size and you know the size of the gas burner inlet thread (1/8" or 1/4" NPT). The default orifice size is #61 and it can be drilled larger for low pressure propane or natural gas.

Specify your fuel preference of natural gas, low pressure propane, or high pressure propane in the Comments section of the shopping cart.

GasHosesandRegulators will drill it (no extra charge) to the proper orifice size for your particular fuel.

Free shipping to the 48 contiguous U.S. States.

CVO125
(1/8" M NPT X 3/8" M GF)
CVO250
(1/4" M NPT X 3/8" M GF)

Shown below is a CVO needle valve control on a straight pipe burner:

$39.95

HPOCA4 - 4" Neck Cast Iron High Pressure Burner

HPOCA4

HPOCA4 - 4" Neck Cast Iron High Pressure Burner. (160,000 BTU/hr)

● The burner has a 6mm in diameter or a 1/4" Center Bolt.
● From the edge of the air inlet to the center bolt the burner is 5".
● From the orifice to the center bolt is 6".
● The total length of the burner with an orifice is 8".
● The diameter of the burner head is 4" and the height is 3".
● We recommend a distance of 3" to 4" from burner to the bottom of pot.

● Provides a maximum output of 160,000 BTU/hr.
● Includes a 90° 3/8" flare Orifice, air shutter, and Insect Screen Guard
Or by request a 180° 3/8" flare orifice fitting is also available.

Optional Accesories:

● We recommend our Regulator COM3.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

We offer free shipping to 48 U.S. States. Wt. 3#.13 oz.

HPOCA4 with Optional CVO Control Valve Orifice
- Bottom side view of the HPOCA4

$39.95

HPCAST6 - 6" Neck Cast Iron High Pressure Burner

HPCAST6

HPCAST6 - 6" Neck Cast Iron High Pressure Burner. (160,000 BTU/hr). Installed in most kettle corn machines.

● The burner has a 6mm in diameter or a 1/4" Center Bolt.
● From the edge of the air inlet to the center bolt the burner is 6 1/4".
● From the orifice to the center bolt is 7 1/2".
● The total length of the burner with an orifice is 10".
● The diameter of the burner head is 4" and the height is 3".
● We recommend a distance of 3" to 4" from burner to the bottom of pot.

● Provides a maximum output of 160,000 BTU/hr.
● Includes a 90° 3/8" flare Orifice, air shutter, and a Insect Screen Guard
Or by request a 180° 3/8" flare orifice fitting is also available.

Optional Accesories:

● We recommend our Regulator COM3.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

We offer free shipping to 48 U.S. States. Wt. 3#.8 oz.

HPCAST6 with Optional CVO Control Valve Orifice
Bottom side view of the HPCAST6
HPCAST6 with Optional G-PILOT Assembly

$59.95

PBM125 - 1 1/4" ID Pipe Burners and Venturi, (with Optional support Legs)

PBM125

PBM125 - 1 1/4" ID Pipe Burners and Venturi, (with Optional support Legs)

● Burners are for High Pressure, Low Pressure Propane or Natural Gas,
   include a 1 1/4" Female NPT venturi and a welded cap on the other end.
● We stock (4) different lengths of pipe burners 32", 44", 56" and 68" which
    are measured from the threads of the pipe burner to the opposite end.
● The burners are 1.25" ID (Inside Diameter) and 1.5" OD
    (Outside Diameter) with the thickness of a standard schedule 40 pipe.
● Our pipe burners are designed to be easily light and they are tested to
    give a blue even flame all across the length of the pipe burner.
● From the theads of the burner to the first drilled hole there is a space of
    8" that does not have any holes for flames this gap is been used as the
    "throat" that is required for the gas and air to mix efficiently in order to
     have a nice blue flame.
● To support the pipe burner we recommend a cradle out of a well
    supported length of angle iron, it will also help for easy an removal
    of the burner for cleaning.

We also have the Option of customized support LEGS which are 1/2" diameter round support legs with or without a flat bar which can be welded permanently to the bottom of the legs.

                                                           Weight    Weight with
                                     LEGS
● PBM125-32, has 32" of total length and 24" of flame     8#        10#
● PBM125-44, has 44" of total lenght and 36" of flame 10#      12#
● PBM125-56, has 56" of total lenght and 48" of flame 12#    15#
● PBM125-68, has 68" of total lenght and 60" of flame 15#    18#

Optional Accesories:

● We recommend our COM3 Regulator for a High Pressure set up.
● We recommend our Regulator COM5 for a Low Pressure set up.
    We recommend our natural gas hoses for a Natural Gas set up.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

● Pipe Burner Video

Pipe Burners are made out of Schedule 40 Black Pipe (Carbon Steel Pipe)

For custom length Stainless Steel pipe burners call for a quote. 713.222.6095

We offer free shipping to 48 U.S. States.

68" Pipe Burner with 1 1/4" FNPT Venturi and Optional CVO Control Valve Orifice (Needle Valve)
32" Pipe Burner with Optional Support Legs
Pipe Burner with Optional G-PILOT Assembly

$299.95

PBMG125 - 1 1/4" ID Pipe Burners with Venturi and Grease Shield (Optional support Legs)

PBMG125

PBMG125 - 1 1/4" ID Pipe Burners with Venturi and Grease Shield
(Optional support Legs)

● Burners are for High Pressure, Low Pressure Propane or Natural Gas,
   include a 1 1/4" Female NPT venturi and a welded cap on the other end.
● We stock (4) different lengths of pipe burners 32", 44", 56" and 68" which
    are measured from the threads of the pipe burner to the opposite end.
● The burners are 1.25" ID (Inside Diameter) and 1.5" OD
    (Outside Diameter) with the thickness of a standard schedule 40 pipe.
● Our pipe burners are designed to be easily light and they are tested to
    give a blue even flame all across the length of the pipe burner.
● From the theads of the burner to the first drilled hole there is a space of
    8" that does not have any holes for flames this gap is been used as the
    "throat" that is required for the gas and air to mix efficiently in order to
     have a nice blue flame.
● To support the pipe burner we recommend a cradle out of a well
    supported length of angle iron, it will also help for easy an removal
    of the burner for cleaning.

We also have the Option of customizing support LEGS which are 1/2" diameter round support legs with or without a flat bar which can be welded permanently to the bottom of the legs.

                                                           Weight    Weight with
                                         GS & LEGS
● PBM125-32, has 32" of total length and 24" of flame 12#          14#
● PBM125-44, has 44" of total lenght and 36" of flame 16#      18#
● PBM125-56, has 56" of total lenght and 48" of flame 20#    22#
● PBM125-68, has 68" of total lenght and 60" of flame 24#    26#

Optional Accesories:

● We recommend our COM3 Regulator for a High Pressure set up.
● We recommend our Regulator COM5 for a Low Pressure set up.
    We recommend our natural gas hoses for a Natural Gas set up.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

● Pipe Burner Video

Pipe Burners are made out of
Schedule 40 Black Pipe
(Carbon Steel Pipe)

For custom length Stainless Steel pipe burners call for a quote. 713.222.6095

We offer free shipping to 48 U.S. States.

32" Pipe Burner with Grease Shield and Optional Support Legs

Pipe Burner with Optional G-PILOT Assembly

$349.95

1 1/4in ID Pipe Burners with Venturi and Grease Shield (Optional support Legs)

LPCAST10-2 - Adjustable Length Neck Cast Iron Low Pressure Propane or Natural Gas Two-Part Burner

LPCAST10-2

LPCAST10-2 - 10" Diameter Burner Head w/ Adjustable Length Neck. Low Pressure Propane or Natural Gas Two-Part Burner (100,000 BTU/hr)

● Designed for the burner head to be placed inside the burning area
and the venturi to be placed on the outside of the system or away
from the burning area, which the distance in between is
determined by the length of a 1 1/4" black pipe nipple been used.
● Venturi and Burner head have 1 1/4" Female Normal Pipe Threads.
● The burner head has (4) 8mm mounting bolts to the sides of the burner.
● The diameter of the burner head is 10" and the height is 5".
● We recommend a distance of 2" from burner to the bottom of pot.

● Provides a maximum output of 100,000 BTU/hr.
● Includes a 90° 3/8" flare Orifice, air shutter, and Insect Screen Guard
Or by request a 180° 3/8" flare orifice fitting is also available.
● 1 1/4" ID Pipe Nipple is NOT included. Pipe nipple must be at least 4".

Optional Accesories:

● We recommend our Regulator COM5 for low pressure propane
● We recommend our natural gas hoses for a natural gas set up.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

We offer free shipping to 48 U.S. States. Wt. 15#.

LPCAST10-2 with Optional CVO Needle Valve Orifice
Bottom view of the LPCAST10-2
LPCAST10-2

$249.95

10in Diameter Burner Head with Adjustable Length Neck Cast Iron Low Pressure Propane or Natural Gas Two-Part Burner

LPCAST8-2 - Adjustable Length Neck Cast Iron Low Pressure Propane or Natural Gas Two-Part Burner

LPCAST8-2

LPCAST8-2 - 8" Diameter Burner Head - Adjustable Length Neck & Height Cast Iron Low Pressure Propane or Natural Gas Two-Part Burner. (80,000 BTU/hr). Home brewers love this versatile burner.

● Designed for the burner head to be placed inside the burning area
and the venturi to be placed on the outside of the system or away
from the burning area, which the distance in between is
determined by the length of a 1 1/4" black pipe nipple been used.
● Venturi and Burner head have 1 1/4" Female Normal Pipe Threads.
● The burner head has (4) 6mm mounting bolts to the sides of the burner.
● The diameter of the burner head is 8" and the height is 6".
● We recommend a distance of 2" from burner to the bottom of pot.

● Provides a maximum output of 80,000 BTU/hr.
● Includes a 90° 3/8" flare Orifice, air shutter, and Insect Screen Guard
Or by request a 180° 3/8" flare orifice fitting is also available.
● 1 1/4" ID Pipe Nipple is NOT included. Pipe nipple must be at least 4".
● This burner is our own design and is not available elsewhere.

Optional Accesories:

● We recommend our Regulator COM5 for low pressure propane
● We recommend our natural gas hoses for a natural gas set up.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

We offer free shipping to 48 U.S. States. Wt. 12#.

LPCAST8-2 with standard 90º brass orifice
LPCAST8-2 with Optional CVO250
Bottom view of the LPCAST8-2
Novel design of LPCAST8-2 casting permits a pipe nipple of any length to enter from below

$199.95

8in Diameter Burner Head with Adjustable Length Neck Cast Iron Low Pressure Propane or Natural Gas Two-Part Burner

LPCAST10 - 10" Neck Cast Iron Low Pressure Propane or Natural Gas Burner

LPCAST10

LPCAST10 - 10" Diameter Burner Head with 10" Neck Cast Iron
Low Pressure Propane or Natural Gas Burner. (100,000 BTU/hr)

● The burner head has (4) 8mm mounting bolts to the sides of the burner.
● From the edge of the air inlet to the center of the burner is 10".
● From the orifice to the center of the burner is 11".
● The total length of the burner with an orifice is 17".
● The diameter of the burner head is 10" and the height is 5".
● We recommend a distance of 2" from burner to the bottom of pot.

● Provides a maximum output of 100,000 BTU/hr
● Proprietary cast mold designed for consistent high performance.
● Includes a 90° 3/8" flare Orifice, air shutter, and Insect Screen Guard
Or by request a 180° 3/8" flare orifice fitting is also available.

Optional Accesories:

● We recommend our Regulator COM5 for low pressure propane
● We recommend our natural gas hoses for a natural gas set up.
● The G-CVO Needle Control Valve Orifice.
● Also our G-PILOT Assembly.

We offer free shipping to 48 U.S. States. Wt. 14#.

LPCAST10 with Optional CVO Needle Valve Orifice
Bottom view of the LPCAST10

$149.95

10in Diameter Burner Head with 10in Neck Cast Iron Low Pressure Propane or Natural Gas Burner

CSB1-COM - Cooker Stand COMBO, Single Burner

CSB1-COM

CSB1-COM - Cooker Stand COMBO, Single Burner. For High Pressure,
Low Pressure or Natural Gas. Includes (4) Leg Extensions, Wind Guard,
(2) WINGS and Regulator Assembly or 5ft Natural Gas Hose.

This Cooker Stand has a cook top of 8 spokes the surface its 15" x 15"
and the height of 15". The CS1 its a dual height stand of 15" or 30".
Includes (4) removable legs that will provide the stand to be 30" in height.
It also comes with a burner of your choice for High Pressure Propane,
Low Pressure Propane or Natural Gas. In the burner there is a CVO125
(Control Valve Orifice) to adjust the flame directly from the burner.

COMBO includes: 8" high WG1 folding Wind Guard, (2) 12" x 14" WING
Side Table Extensions and a propane regulator assembly according to the
set up you chose high pressure or low pressure or a 5ft natural gas hose.
(COMBO setup saves almost $23.00 over buying all the items separately!)

● High Pressure Propane, with (1) HPCAST6 Burner (160,000 btu/hr).
   Includes a COM1 Regulator for a high pressure set up.

● Low Pressure Propane, with (1) LPCAST Burner (40,000 btu/hr).
   Includes a COM5 Regulator for a low pressure set up.

● Natural Gas, with (1) LPCAST Burner (40,000 btu/hr).
   Includes a 5' - 3/8"ID natural gas hoses  for a natural gas set up.

Optional Accessories:

Check out our Small GRIDDLES and our BACON PRESS.
Also the RING1 11" x 2" Wok Ring and RING2 9" x 3" Wok Ring.
And the 7CSB1,, Single Burner Cooker Stand Heavy Duty Cover.

15"L x 15"W x 15"H, with the legs installed 15"L x 15"W x 30"H.
We offer free shipping to 48 U.S. States. Wt. 46#.

The CSB1H-COM Base Unit Can Be Used As a Cooker Stand and
Placed either on the Ground or on an Elevated Fireproof Surface

$800.00

Cooker Stand COMBO, Single Burner. For High Pressure, Low Pressure or Natural Gas. Includes (4) Leg Extensions, Wind Guard, (2) WINGS and Regulator Assembly or 5ft Natural Gas Hose.

CSB1 - Cooker Stand, Single Gas Burner Outdoor Picnic Cooking Stand Stove

CSB1

CSB1 - Cooker Stand Single Gas Burner Outdoor Picnic Cooking Stand Stove. For High Pressure, Low Pressure or Natural Gas. Includes (4) Leg Extensions.

This Cooker Stand has a cook top of 8 spokes the surface its 15" x 15"
and the height of 15". The CSB1 its a dual height stand of 15" or 30".
Includes (4) removable legs that will provide the stand to be 30" in height.
It also comes with a burner of your choice for High Pressure Propane,
Low Pressure Propane or Natural Gas. In the burner there is a CVO125
(Control Valve Orifice) to adjust the flame directly from the burner.

● High Pressure Propane, with (1) HPCAST6 Burner (160,000 btu/hr).
   We recommend our COM1 Regulator for a high pressure set up.

● Low Pressure Propane, with (1) LPCAST Burner (40,000 btu/hr).
   We recommend our COM5 Regulator for a low pressure set up.

● Natural Gas, with (1) LPCAST Burner (40,000 btu/hr).
   We recommend our natural gas hoses for a natural gas set up.

Optional Accessories:

The Optional WING side table extensions work well with this unit and the
Optional WG1, 8" high single burner folding Wind Guard is available.
Check out the RING1 11" x 2" Wok Ring and RING2 9" x 3" Wok Ring.
Also the Small GRIDDLES and our BACON PRESS.
And the 7CSB1, Single Burner Cooker Stand Heavy Duty Cover.

15"L x 15"W x 15"H, with the legs installed 15"L x 15"W x 30"H.
We offer free shipping to 48 U.S. States. Wt. 27#.

CSB1H shown without the (4) Leg
Extensions Which Are Included

$450.00

CSB12 - Low Pressure Propane or Natural Gas Single Burner Cooker Stand with a 12" Diameter 120,000 Btu/hr Burner

CSB12

CSB12 - Low Pressure Propane or Natural Gas Single Burner
Cooker Stand with a 12" Diameter Cast Iron (120,000 btu/hr) Burner.

This Cooker Stand has a cook top of 8 spokes the surface its 15" x 15"
and the height of 15". The CSB12 its a dual height stand of 15" or 30".
Includes (4) removable legs that will provide the stand to be 30" in height.
Designed for more btu/hr output on natural gas or low pressure propane.
The 12" wide burner surface gives more heat over a wider area on the
bottom of your pans or pots. The burner comes with a CVO250
(Control Valve Orifice) to adjust the flame directly from the burner.

Optional Accessories:

We recommend our COM5 Regulator for a low pressure set up.
We recommend our natural gas hoses for a natural gas set up.
The Optional WING side table extensions work well with this unit and the
Optional 8" high single burner folding Wind Guard is available.
Check out the RING1 11" x 2" Wok Ring and RING2 9" x 3" Wok Ring.
Also the Small GRIDDLES and our BACON PRESS.
And the 7CSB12, Single Burner Cooker Stand Heavy Duty Cover.

15"L x 15"W x 15"H, with the legs installed 15"L x 15"W x 30"H.
We offer free shipping to 48 U.S. States. Wt. 47#.

CSB12-N Cooker Stand for Natural Gas Which Outputs
Up To 120,000 btu/hr! Shown Without the Included Legs
Also Available for Use with Low Pressure Propane

$700.00

Low Pressure Propane or Natural Gas Single Burner Cooker Stand with a 12" Diameter 120,000 Btu/hr Burner

CSB12-COM - Low Pressure or Natural Gas Single Burner Cooker Stand COMBO with a 12" Diameter 120,000 Btu/hr Burner

CSB12-COM

CSB12-COM - Low Pressure Propane or Natural Gas Single Burner
Cooker Stand COMBO with a 12" Diameter (120,000 btu/hr) Burner.
Includes (4) Leg Extensions, Wind Guard, (2) WINGS and
Regulator Assembly or 5ft Natural Gas Hose.

This Cooker Stand has a cook top of 8 spokes the surface its 15" x 15"
and the height of 15". The CSB12 its a dual height stand of 15" or 30".
Includes (4) removable legs that will provide the stand to be 30" in height.
Designed for more btu/hr output on natural gas or low pressure propane.
The 12" wide burner surface gives more heat over a wider area on the
bottom of your pans or pots. The burner comes with a CVO250
(Control Valve Orifice) to adjust the flame directly from the burner.

COMBO includes: 8" high folding Wind Guard, (2) 12" x 14" WING
Side Table Extensions and a COM5 Regulator or a 5 ft. natural gas hoses.

Optional Accessories:

Check out our GRIDDLES and our BACON PRESS.
Also the RING1 11" x 2" Wok Ring and RING2 9" x 3" Wok Ring.
And the 7CSB12, Single Burner Cooker Stand Heavy Duty Cover.

15"L x 15"W x 15"H, with the legs installed 15"L x 15"W x 30"H.
We offer free shipping to 48 U.S. States. Wt. 69#.

CSB12-LCOM Cooker Stand Shown Disassembled. Above
Burner Is Set Up For Using Low Pressure Propane

$1000.00

Low Pressure or Natural Gas Cooker Stand COMBO Series with a 12" Diameter 120,000 Btu/hr Burner. Includes (4) Leg Extensions, Wind Guard, (2) WINGS and Regulator Assembly or 5ft Natural Gas Hose.

A75AM - 3/4" Cast Aluminum Venturi Air Gas Mixer, with an air shutter, Insect Screen, and the selected orifice fitting.

A75AM

New Venturi Design

A75AM 3/4" Cast Aluminum Venturi Air Gas Mixer, air shutter, with Insect Screen Guard, and a 90° 3/8" gas flare orifice fitting (or selected orifice type). For use with high or low pressure with the appropriate orifice fitting size.

- Aluminum Casting Made in Houston, Texas. Made-in-U.S.A.

- No Rust, Light Weight and No Paint Needed.

The flat top surface is 3" in diameter by 1-3/4" in height.
The height of the venturi with an orifice is approximately 2-3/4".
Includes an air shutter, Insect Screen Guard, and a 90° 3/8" gas flare orifice fitting. A 180° 3/8" gas flare orifice fitting is also available. Ask.

For High Pressure use we recommend the COM3 regulator/hose.
For Low Pressure use we recommend the COM5 regulator/hose.
The Optional CVO Needle Control Valve with Orifice.
Also available with a T-PILOT Assembly.

Comes with a #61 orifice for High Pressure Propane, OR specify your desired size, and we will custom drill your orifice at no extra charge.

Weight 7 oz. Free shipping within the 48 contiguous U.S. States.

The photos below show the different options which can be choosen from the menu above the price.

Options:

Default A75AM with 90° Orifice, $99.95

A75AM with optional CVO valve orifice, $139.95


A75AM with optional T-PILOT Assembly, $179.95

$99.95

A75AM venturi air gas mixer with 90° Orifice

A125AM - 1 1/4" Cast Aluminum Venturi Gas and Air Mixer

A125AM

A125AM - 1 1/4" Cast Aluminum MONSTER Venturi Gs and Air Mixer.

- Aluminum Casting Made in Houston, Texas. Made-in-U.S.A.

- It has a 1 1/4" Female Normal Pipe Thread Outlet.

- No Rust, Light Weight and No Paint Needed.

- To be used with High Pressure / Low Pressure Propane or
Natural Gas.

- The flat top surface is 4" in Diameter by 2 1/2" in height.
- The height of the venturi with an orifice is approximately 4".

- Includes an Aluminum Air Shutter, Insect Screen Guard and a
90 3/8" Flare Orifice, with #61 Orifice for High Pressure Propane.

- Alternatively, a 180 3/8" Flare Orifice fitting is also available.
- Drilled to custom orifice size depending on your specified fuel and
length of pipe burner or specified burner at No Extra Charge.

(For alternative orifice or custom drilled orifice please let us know the
information in comment box section when added to shopping cart).

For High Pressure use we recommend the COM3 regulator/hose.

For Low Pressure use we recommend the COM5 regulator/hose.

The Optional CVO Needle Control Valve with Orifice.

Also available with a G-Pilot Assembly.

Weight 1#. Free Shipping within the 48 contiguous U.S. States.

$149.95

A125AM - 1 1/4" Cast Aluminum Venturi Gas and Air Mixer